| Customization: | Available |
|---|---|
| Transport Package: | Cartons |
| Specification: | 550*330*3.2 |
|
Still deciding? Get samples of US$ 15/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
This product can be softening and plasticity under the lower temperature and it is a new type of polymers. It character changes according to the temperature. Under the normal room temperature (20 to 30ºC ), the material is solid state, hard texture; Our product can be put into the hot water (The Temperature about 65-75 ºC) about 2-3 minutes, it will be soften, and you can make to any shape. Our product very light, good breath ability, high strength, very good tensile, you can stretch it freely, X-ray permeability very good, no stimulation to the skin, biodegradable.
Application Field:
How to use?
1. Select the applicable positioning mask for head, head neck shoulder or body Mask.
2. Put the mask into the water with constant temperature of 149ºF-167ºF/65-75ºC for 2-3 minutes when the mask changed to transparent and soften. Please take it out and put it on the operation table, dry it with a piece of soft cloth. Put the mask on the suitable fixing part to shape it and fix it on the adapter board.
3 After 2-4 minutes when the mask is in a certain strength, draw the mark line and take it out for the future use.
[Cautions]:
1. When you are heating the material in hot water with about 65-75ºC, the water must below 176ºF(80ºC) be sure to maintain the appropriate time, neither too long nor too short, in general, it is enough to make it soften and activated about 2-3min.
2. After the positioning mask was soften, it could be operated within 2-3 minutes in room temperature surrounding . The surrounding temperature would affect the level of hardening.
3. It is important that the thermoplastic are completely cool before removing it from patient, if remove it when still warm, it will cause additional shrinkage and will be very tight in the patient. A cool, damp towel can help speed the cooling process.
4. Be careful with using.
|
Light weight, easy to carry |
The weight is light, only 1/8 of plaster, wearing comfortable and neat appearance |
|
Strong Plasticity |
Easily shaped by patients' affected positions. Will not rebound after cooling |
|
100% of the memory function |
If it can't fit to the patients well, put it back into the hot water and reshaped. It will be quickly recovered to original and can reuse about 6-8 times and realize cost saving. |
|
Good breath ability. |
The holes on the materials surface can keep good transmittance, avoid necrosis of the affected infection. |
|
Practical |
It has the features of toxic-free tasteless, easy cleaning in cold water after shaped, can wear it during bath, can be penetrated by X-ray, no need to take off when do the X-ray |
|
Eco-friendly |
After 1 year, it can be degraded by itself in natural conditions, no pollution to environment . |
| Good tensile | It has good tensile, can stretch in all direction with 1-1.5 times |
Clients feeback:How to use?
1. Adjust the water temperature to 68ºC-72 ºC , more than 80 ºC will make the mask contraction and deformation.
2. Be sure not to place the mask in hot water for a long time. In general, 2-3 minutes should be enough to make the mask soften and activation.
3. The available time for modeling the mask is 3 '30 ''(3 minutes and 30 seconds)
4. The maximum tensile strength of orthopedic sheet is 1.5 times of its original size; And the maximum tensile strength of the mask product is 6 times of its own. Excessive pulling could affect its reshaped resilience and damage its memory function.
5. How to restore a molding mask back to its factory settings? Just put it into the 68ºC-72ºC water and then it will rebound automatically after 5 minutes.
6. Due to the characteristics of the material itself, in the activation process, it will occasionally occur small area of sticky. Please be sure not to pull randomly. When it leaves the water to solidify, it will automatically relieves adhesion.
FAQ:
1 Q: Are you a factory or trading company?
Answer: We are a real factory. It's easy to be recognized from our website and logo.
2 Q: Can you provide samples for checking before order?
Answer: Yes, we can offer you some free samples for some low-valued sample, you need only to bear the freight cost. For some high-valued sample, we'd like to give you a special discount.
3 Q: How do your guarantee the quality of your products?
Answer: We have professional inspectors to analyze chemical composition of the raw materials, and test the finished products strictly according to standard stipulated in the contract. In this process, two ends appearance, being degree, fixed length etc., will be checked one by one. From production, packaging to transport, we strive to ensure that every link is perfect.
4 Q: What's your MOQ?
Answer: For our low temperature thermoplastic products, one piece should be available.But adding tax, transfer, custom charges, it's not fair for buyers. So a large quantity will be much suitable for all of us.
5 Q: How about the trade terms?
Answer: EXW, FOB, CFR, CIF will be accepted.
6. Q: How about your payment term?
Answer: Paypal, Western Union, L/C is our regular payment terms.
7. Q: What is your delivery time?
Answer: For stocks, we can send the goods to loading port within 7 days after receiving your deposit. For production period, it usually be about 10days-15days.
8. Q: Where did you export?
Answer: USA, Canada, Japan, Southeast Asia, Eastern Europe, South Africa, South America, etc.
9. Q: Can you supply OEM products under my brand?
Answer: Yes, It's Ok.
10. Q: Can I become a exclusive distributor of your products in my area?
Answer: Yes, it is possible.
11. Q: When and how could I touch you?
Answer: 7days a week&24 hours. I'm a workaholic, so you could touch me anytime you like.
As Long Time As You Need, As Long Time As I Have!
Touch Me for Free Samples!!
){kind=link}